Other Images (click to see large image)

| |

Design:

Alloy Sea Boat 6 metre Walk A Round

Length:

6 ,6.5 or 7. Metres

Displacement:

1190 (6 M light) KG

Material:

Aluminium

Hull Draft:

0.30 Metres

LWL:

Metres

Hull Weight:

650 (alloy matl) KG

Beam:

2.45 Metres

Max Speed:

30+ Knots

Motor Cap:

2 X 80 HP

Fuel Type:

Petrol

Fuel Cap:

200 Litres

Alt Config:

Hard Top, Centre Console, Raised Fore Deck, Outboard Well, Full or half pod.

Can be built 6, 6.5 or 7 metres by adding additional frames. Also available in a reduced version that is reduced overall by 7% to a length of 5.58 metres for persons wanting a lighter boat for towing with their existing vehicle.

Other Info:

Aluminium plate 5mm on bottom and 4mm on side.
Frames 80 X 6mm flat bar

Comments:

This design is a conventional 15 degree constant deadrise single chine hull with an outer chine strake angled down at 5 degrees. The conical developed forward bottom has a fine entry and the top sides forward have a single line flare.

Most popular version is a single pod with boarding platform and walk through stern door.

Alloy Sea Boat 6 metre Walk A Round

PRICE: $US 395.00

What is included in the stock Plan.

For more infomation about stock plans have a look here

How to use Member Questions
To access the answers to these questions you must be logged in as a member of the boden boat plans website. Once you are logged in simply click any of the questions to see the answer.

Ask a question
If your question has not been asked please click here to ask your question. Please remember that you have to be Boden Boat Plans member.
 

From all the above-written answers I guess that lines plan and table of offsets are included into full plan of Alloy Sea Boat 6 m. Am I right ?

Hello from Canada.
I would like to know how stable this boat is at low spead and dead stop. I would also like to know if this boat could be disighned with a split windshield open self bailing bow platform I'm looking for as much open deck space as posible and still have a full windsheild possibly withsoft top.

Thankyou Robert Daffurn

I am interested in the 5.58 mt version of the alloy sea boat.Is this boat suitable to cross a bar.Is there any pictures of this version available. Is there any more iformation I can access. Regards mike stephens.

will this design in the 7 meter length accomodate a single outboard or sterndrive configuration in the 225 hp range??

Can this boat in a 7meter length support a single 225hp 4 cycle motor?

Isthe 5.58 available in a raised foredeck and a center cab

Can you make available an estimate of the cost of materials required to construct the hull and superstructure (but not the interior finishing) for the 6m boat pictured?

to ask the question in Whatis the best finish for the boat, can it be left unpainted ifused in salwater-if painting is
recomended can this be done succesfully without a drying oven

to ask the question in
are DXF files available to convert into cnc
cutting files

Would a 165amp welder be capable of welding the 3mm aluminium for this craft?

Can this boat be built as a walk around cab?
Will the stern support 2/60 hp 4 strokes?

is it possible to increase the deadrise to 17 or 18 degrees and use a larger reverse shine on the 2.45 beam. Plus the walkaround cab, can this be raised for more headroom in the bunks in the raisedfore deck version

With the 6m alloy seaboat. A raised forward sheer in half or cuddy design and full pod. Is this possible? I would also prefer a under floor fuel tank. Can you please supply approximate hull weight and full length thankyou.

Is this boat suitable for commercial fishing??

My question on under floor tanks.
Is it possible to email a rough sketch of the position of these above floor tanks?
[email protected] (I would grateful)

Where I can find other photoes of Alloy Sea Boat ?

to ask the question in Can this boat be built sucessfully by a first time builder at home

Would this design take a jet drive and if so what size diesel/petrol engine would it need to match the twin 80 ob performance.

Hi
Where can you get the aliminium at $7ish a kilo i am in Hervey Bay QLD but would order it from down south if i knew where. alloy price and knowing where to get it is the only thing holding me back from starting
hope you can help
Terry E

hi what hp 4stroke outboard (single) is required for the 5.8m version to get go holeshot and cruise speeds

Your pdf document states that this craft will achieve 35 kts fully loaded with 150hp. What sort of engines/engine is required to achieve the quoted 40+ knts on the initial web page for this boat. Does 2 80hp engines equal a single 160hp or is it not that simple? I asume that a single large engine installation would work out cheaper and easier than 2 smaller engines.

Do you have any links for boat trailer plans? If I actually follow thru and build a 7m tinnie it would seem a cop out to buy a trailer rather than build one to suit.

If a Hamilton Jet where to be used on this design, I assume that a V8 marinised car engine would be used also? If this were the case would the fuel consuption be horrendous compared to a similiary matched single outboard. What sort of speed would you get with a Jet and a V8? Say a 308?

What is the minimum and maximum power range for the vessel. I am not interested in speed but more cost of the powerplant, preferably a single engine.

HI'
Iam very interested in buying the pull set off plan's off the alloy sea boat 6 metre
can you tell me the price in aus dollar's
MANY THANK'S
PETER

regarding my question on underfloor tanks. Why do you not reccomend this option?
I,m looking for deck space for fishing and I also have to cater for smaller children. this is why I asked about this option

can 6 metr alloy boat picture made a full cabin cruser for inland or the 6.5meter and make available estimate cost of hull and superstructure only and the type of diesel motor will you recomended if can by available . regards carlos bairo

will the 6metr alloy support a diesel stern drive? I'm looking at the Cummins Mercruiser 1.7 MS (120hp) which weighs aprox 300kg engine and leg

when you buy the full plans on pdf what does it take to get this converted into a program that my local metal work shop can use on there computer controlled plasma or router cutter kind regards simon oakley